Exactly How to Install a Bath Tub Yourself: Removing and Replacing.
Exactly How to Install a Bath Tub Yourself: Removing and Replacing.
Blog Article
The article listed below relating to A Step-by-Step Guide to Installing a Bathtub is really motivating. You should see for yourself.
Installing a bathtub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately difficult task. If the old tub is conveniently accessible, the task can move speedily; if you need to open a wall surface to remove the old bathtub and place the new bath tub, the task is a lot harder. In either instance, the task is within a house handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. See to it you have actually qualified on your own for the task and are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is far better to think about utilizing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly assist you set up a brand-new bathtub in your shower room if you have actually already acquired a brand-new tub as well as do not need to alter the setup of your previous water supply pipes.
Your devices and also material list need to comprise the following:
Planning for the Setup
To start with, the sustaining structure provided with the bath should be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the limited accessibility that is typically the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming during this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bathtub in the needed setting. The wood boards are useful in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following goal is to make sure that the tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the tub till the level reads level.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the proper supply pipeline by making a compression join; after that do the very same for the various other tap.
Turn on the supply of water and also inspect all joints as well as new pipework for leakages and also tighten them if needed. Load the tub and additionally inspect the overflow electrical outlet and the regular electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and also securing around the bathtub must wait until the tub has actually been utilized at least once as this will certainly settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in place with the maker provided backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be linked to the tap finishes initially, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a rigid seal, triggering the water to penetrate the wall between the bath and the tiling, causing issues with moisture and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and also can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can split rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very taken with A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed the new piece. Appreciated our article? Please share it. Help other people locate it. I appreciate reading our article about Installing A Bathtub.
Schedule And Pricing Report this page